View ACA2402RS7P0_5363389.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

12/2008 aca2402 750/870/1000 mhz catv push-pull line amplifer data sheet - rev 2.2 figure 1: hybrid application diagram features ? 1 ghz specifed performance ? 22 db gain ? very low distortion ? excellent 75 ? input and output match ? stable with high vswr load conditions ? monolithic design for consistent performance part-to-part ? low dc power consumption ? surface mount package compatible with automatic assembly ? low cost alternative to hybrids ? meets cenelec standards ? materials set consistent with rohs directives. applications ? catv line amplifers, system amplifers, distribution nodes product description the aca2402 is a highly linear, monolithic gaas rf amplifer that has been developed as an alternative to standard catv hybrid amplifiers. offered in a convenient surface mount package, the mmic consists of two pairs of parallel amplifers that are optimized for exceptionally low distortion and noise fgure. a s7 package 16 pin wide body soic with heat slug hybrid equivalent that provides fat gain response and excellent input and output return loss over the 40 to 1000 mhz catv downstream band is formed when one aca2402 is cascaded between two appropriate transmission line baluns. rf input rf output 2a 2b 1b 1a aca2402
2 data sheet - rev 2.2 12/2008 aca2402 figure 2: pin out table 1: pin description 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 gnd gnd i set 2a in gnd 2b in 1b in 1a in gnd gnd 1b ou t 2b ou t 2a ou t 1a ou t bias 1a bias 1b pin name description pin name description 1 gnd ground 16 gnd ground 2 2a in amplifier 2a input 15 1a out amplifier 1a output 3 gnd ground 14 bias 1a bias for 1a amplifier 4 1a in amplifier 1a input 13 2a out amplifier 2a output and supply 5 1b in amplifier 1b input 12 2b out amplifier 2b output and supply 6 1 set current adjust 11 bias 1b bias for 1b amplifier 7 2b in amplifier 2b input 10 1b out amplifier 1b output 8 gnd ground 9 gnd ground
data sheet - rev 2.2 12/2008 3 aca2402 table 2: absolute mimimum and maximum ratings electrical characteristics stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges notes: 1. pins 2, 4, 5 and 7 should be ac-coupled. no external dc bias should be applied. 2. pin 6 should be ac-grounded and/or pulled to ground through a resistor for current control. no external dc bias should be applied. 3. pins 11 and 14 are bias feeds for input amplifers 1a and 1b. no external dc bias should be applied. 4. pins 10 and 15 receive dc bias directly from pins 11 and 14. no other external bias should be applied. the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifcations. parameter min max unit 6xssoslqv 0 +28 vdc 53rhdsxvslv - +75 p9 6rdh7hpshdxh -65 +150 c 6rhl7hpshdxh - +260 c 6rhl7lph - 5.0 6h parameter min typ max unit 6xsso9 d d slv - +24 - vdc 5htxh 40 - 1000 mhz dvh7hpshdxh -40 - +110 c
4 data sheet - rev 2.2 12/2008 aca2402 table 4: ac and dc electrical specifcations (t a = +25 c, v d d = +24 vdc) notes: (1) measured with baluns on the input and output of the device. (2) parts measured with 77 channels fat output, +42 dbmv per channel. (3) parts measured with 110 channels fat output, +40 dbmv per channel. (4) parts measured with 128 channels fat output, +40 dbmv per channel. (5) the supply current may be reduced by decreasing the value of r3 (see figure 17) (6) 47.5 dbmv output, 9.5 db tilt @ 1 ghz (7) 45.5 dbmv output, 9.5 db tilt @ 1 ghz 8. all specifcations as measured on evaluation board (see figures 16 & 17). parameter min typ max unit comments dlq0+ 21.1 21.6 22.1 dhtxldh6rsh - 0 - dldhvv 0+ - ? 0.2 - 1rlvhlxh - 3.5 4.5 7 77 channels dhvsxv40r+ 110 channels dhvsxv40r+ 128 channels - - - - - -76 - -73 - -70 -74 -74 -71 -71 - 62 77 channels dhvsxv40r+ 110 channels dhvsxv40r+ 128 channels - - - - - -72 - -72 - -69 -70 -70 -70 -68 - 02 77 channels dhvsxv40r+ 110 channels dhvsxv40r+ 128 channels - - - - - -65 - -65 - -62 -63 -63 -63 -63 - 5hx/rvvsx2xsx 18 22 - 75 ? 240 250 260 ma 7hpd5hvlvdh - - 3.8 2
data sheet - rev 2.2 12/2008 5 aca2402 performance data figure 4: gain (s21) vs. frequency 2 2. 5 3 3. 5 4 4. 5 5 01 00 200 30 04 00 50 06 00 700 800 90 01 00 0 frequenc y (mhz ) noise figure (db ) figure 3: noise figure vs frequency
6 data sheet - rev 2.2 12/2008 aca2402 figure 5: input and output return loss (s11 and s22) vs. frequency figure 6: isolation (s12) vs. frequency -4 0 -3 5 -3 0 -2 5 -2 0 -1 5 -1 0 -5 0 5 01 00 200 300 400 500 600 700 800 900 1000 1100 1200 frequenc y (m hz ) s22 (db) s1 1 s2 2
data sheet - rev 2.2 12/2008 7 aca2402 figure 7: ctb vs. output power at worst-case channel/frequency (128 total channels, 110 analog channels, fat output) figure 8: cso vs. output power at worst-case channel/frequency (128 total channels, 110 analog channels, fat output) figure 9: xmod vs. output power at worst-case channel/frequency (128 total channels, 110 analog channels, fat output)
8 data sheet - rev 2.2 12/2008 aca2402 figure 10: ctb vs. frequency (110 channels, +40 dbmv power, fat output) figure 11: cso vs. frequency (110 channels, +40 dbmv power, fat output) figure 12: xmod vs. frequency (110 channels, +40 dbmv power, fat output) -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 0 1 00 200 300 400 50 0 6 00 70 0 8 00 ctb (dbc) frequency (mhz) -100 -9 5 -9 0 -8 5 -8 0 -7 5 -7 0 -6 5 -6 0 -5 5 -5 0 0 100 200 300 400 500 600 700 800 frequenc y( mh z) cs o ( dbc) - 100 -9 5 -9 0 -8 5 -8 0 -7 5 -7 0 -6 5 -6 0 -5 5 -5 0 0 100 200 300 400 500 600 700 800 frequency (mhz) xmod (dbc)
data sheet - rev 2.2 12/2008 9 aca2402 figure 13: ctb vs. frequency (77 channels, +42 dbmv power, fat output) figure 14: cso vs. frequency (77 channels, +42 dbmv power, fat output) figure 15: xmod vs. frequency (77 channels, +42 dbmv power, fat output) -100 -9 5 -9 0 -8 5 -8 0 -7 5 -7 0 -6 5 -6 0 -5 5 -5 0 0 100 200 300 400 500 600 ctb (dbc) frequency (mhz) - 100 -9 5 -9 0 -8 5 -8 0 -7 5 -7 0 -6 5 -6 0 -5 5 -5 0 0 100 200 300 400 500 60 0 cso (dbc) frequency (mhz) -100 -9 5 -9 0 -8 5 -8 0 -7 5 -7 0 -6 5 -6 0 -5 5 -5 0 0 1 00 20 0 3 00 40 0 5 00 600 xmod (dbc) frequency (mhz)
10 data sheet - rev 2.2 12/2008 aca2402 application information figure 16: evaluation board layout figure 17: evaluation board schematic notes: 1. via holes should be 35 mils (0.89 mm) in diameter, and plated to 1 mil (0.025 mm) thickness. they need not be solder- flled. 2. warning: due to the power dissipation of this device, the printed circuit board should be mounted/attached to a heat sink. 3. more assembly details, such as via hole diameters, via spacing, solder paste application, and soldering recommenda - tions are provided in the application note entitled, thermal management of anadigics surface mounted amplifers.
data sheet - rev 2.2 12/2008 11 aca2402 table 5: evaluation board parts list notes: (1) n connector center pin should be approximately 80 mils in length. (2) t1, t2 balun: 5.5 turns thru, as shown in figure 18. (3) 200 ma minimum current rating. figure 18: balun drawing ref description qty vendor vendor p/n c1, c2, c3, c6, c7, c10, c14 0.01 ? f chip cap 7 murata grm39x7r103k50v c4, c5, c8, c9 470 pf chip cap 4 murata grm39x7r471k50v c12, c13 1.0 pf chip cap 2 murata grm36cog1r0c50 c15 47 ? f elect. cap 1 digi-key corp p5275-nd r1, r2, c11 not used r3 18 k ? resistor 1 digi-key corp p18kgct-nd tvs tvs 24 volt 600 watt 1 digi-key corp smbj24accct-nd l1, l2, l3, l4 (3) 680 nh inductor 4 coilcraft 1008cs-681xkbc connector (1) 75 ? n male panel mount 2 pasternack enterprises pe4504 t1, t2 (2) (balun) ferrite core 2 fa ir-rite 2843002702 wire mws wire ind. t-2361429-20 printed circuit board 1 standard printed circ. inc 24vx1ac50 ind ium 300 x 160 mils 1 indium corp of america 14996y
12 data sheet - rev 2.2 12/2008 aca2402 figure 19: s7 package outline - 16 pin wide body soic with heat slug package outline
warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. important notice anadigics, inc. 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com e-mail: mktg@anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.2 12/2008 13 aca2402 ordering information order number temperature range package description component packaging aca2402s7tr -40 to 110 o c 16 pin wide body soic with heat slug 1,500 piece tape and reel aca2402rs7p2 -40 to 110 o c rohs-compliant 16 pin wide body soic with heat slug 1,500 piece tape and reel aca2402s7p0 -40 to 110 o c 16 pin wide body soic with heat slug plastic tubes (50 pieces per tube) ACA2402RS7P0 -40 to 110 o c rohs-compliant 16 pin wide body soic with heat slug plastic tubes (50 pieces per tube)

▲Up To Search▲

Price & Availability of ACA2402RS7P0

	To Download ACA2402RS7P0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .